Author: Laurel Hamers / Source: Science News
Off a gravel road at the edge of a college campus — next door to the town’s holding pen for stray dogs — is a busy test site for the newest technologies in drinking water treatment.
In the large shed-turned-laboratory, University of Massachusetts Amherst engineer David Reckhow has started a movement. More people want to use his lab to test new water treatment technologies than the building has space for.
The lab is a revitalization success story. In the 1970s, when the Clean Water Act put new restrictions on water pollution, the diminutive grey building in Amherst, Mass. was a place to test those pollution-control measures. But funding was fickle, and over the years, the building fell into disrepair. In 2015, Reckhow brought the site back to life. He and a team of researchers cleaned out the junk, whacked the weeds that engulfed the building and installed hundreds of thousands of dollars worth of monitoring equipment, much of it donated or bought secondhand.
“We recognized that there’s a lot of need for drinking water technology,” Reckhow says. Researchers, students and start-up companies all want access to test ways to disinfect drinking water, filter out contaminants or detect water-quality slipups. On a Monday afternoon in October, the lab is busy. Students crunch data around a big table in the main room. Small-scale tests of technology that uses electrochemistry to clean water chug along, hooked up to monitors that track water quality.
On a lab bench sits a graduate student’s low-cost replica of an expensive piece of monitoring equipment. The device alerts water treatment plants when the by-products of disinfection chemicals in a water supply are reaching dangerous levels. In an attached garage, two startup companies are running larger-scale tests of new kinds of membranes that filter out contaminants.
BACK TO LIFE
Parked behind the shed is the almost-ready-to-roll newcomer. Starting in 2019, the Mobile Water Innovation Laboratory will take promising new and affordable technologies to local communities for testing. That’s important, says Reckhow, because there’s so much variety in the quality of water that comes into drinking water treatment plants. On-site testing is the only way to know whether a new approach is effective, he says, especially for newer technologies without long-term track records.
The facility’s popularity reflects a persistent concern in the United States: how to ensure affordable access to clean, safe drinking water. Although U.S. drinking water is heavily regulated and pretty clean overall, recent high-profile contamination cases, such as the 2014 lead crisis in Flint, Mich. (SN: 3/19/16, p. 8), have exposed weaknesses in the system and shaken people’s trust in their tap water.
Tapped out
In 2013 and 2014, 42 drinking water–associated outbreaks resulted in more than 1,000 illnesses and 13 deaths, based on reports to the U.S. Centers for Disease Control and Prevention. The top culprits were Legionella bacteria and some form of chemical, toxin or parasite, according to data published in November 2017.
Those numbers tell only part of the story, however. Many of the contaminants that the U.S. Environmental Protection Agency regulates through the 1974 Safe Drinking Water Act cause problems only when exposure happens over time; the effects of contaminants like lead don’t appear immediately after exposure. Records of EPA rule violations note that in 2015, 21 million people were served by drinking water systems that didn’t meet standards, researchers reported in a February study in the Proceedings of the National Academy of Sciences. That report tracked trends in drinking water violations from 1982 to 2015.
The Safe Drinking Water Act regulates levels of contaminants in public water supplies. This graph tracks violations of the act over time. Spikes in violations often coincide with new, more stringent rules.
Water quality violations in U.S. water systems
Current technology can remove most contaminants, says David Sedlak, an environmental engineer at the University of California, Berkeley. Those include microbes, arsenic, nitrates and lead. “And then there are some that are very difficult to degrade or transform,” such as industrial chemicals called PFAS.
Smaller communities, especially, can’t always afford top-of-the-line equipment or infrastructure overhauls to, for example, replace lead pipes. So Reckhow’s facility is testing approaches to help communities address water-quality issues in affordable ways.
Some researchers are adding technologies to deal with new, potentially harmful contaminants. Others are designing approaches that work with existing water infrastructure or clean up contaminants at their source.
How is your water treated?
A typical drinking water treatment plant sends water through a series of steps.
First, coagulants are added to the water. These chemicals clump together sediments, which can cloud water or make it taste funny, so they are bigger and easier to remove. A gentle shaking or spinning of the water, called flocculation, helps those clumps form (1). Next, the water flows into big tanks to sit for a while…
The post Engineers are plugging holes in drinking water treatment appeared first on FeedBox.